45mil EPDM Liner, Sizes from 5' x 5' to 50' x 100'Firestone pond liners are the industry standard for 45 mil EPDM. You can rest assured that your aquatic life will be safe, because these pond liners contain none of the algaecides & fire retardants found in roofing EPDM.
If your pond liner has a minor tear, fix it quickly and easily using the Firestone EPDM Liner Repair Kit. This kit contains all you need to quickly and easily repair minor damages to your liner.
Firestone Lap Sealant HS - 11oz TubeFirestone Lap Sealant HS is a low volatile organic compound (LVOC) sealant designed to be used with Firestone Splice Adhesive SA-1065 for seam edge treatment applications and as a sealant in other applications as indicated by current Firestone specifications and details.
Firestone QuickPrime™ Plus - Quart SizeFirestone QuickPrime™ Plus is designed to clean and prime Firestone membranes prior to application of QuickSeam™ products, where required by Firestone Specialty Products specifications and details.
Firestone QuickRoller™ ApplicatorThe Firestone QuickRoller™ consists of a 42.0” steel handle attached to a rubber-sleeved steel roller. The QuickRoller™ is designed to assist in binding Firestone QuickSeam™ products with Firestone membranes and other liners.
Firestone QuickScrubber™ KitThe Firestone QuickScrubber™ Kit consists of a scrub pad and holder that allows application of QuickPrime™. When proper pressure is applied, the handle flattens out assuring that proper pressure is maintained.
Firestone QuickSeam™ Cover Strip (Single-Sided Seam Tape)The Firestone QuickSeam™ Batten Cover Strip is a 6" wide semi-cured EPDM strip laminated to a QuickSeam™ tape. Unlike the 3" tape (which is double-sided to go between two overlapping layers of liner), this self-adhesive cover tape overlaps the seam.
Firestone QuickSeam™ Corner Flashing is a self-adhesive, 8.5" diameter piece of uncured EPDM FormFlash laminated to QuickSeam™ tape. It is designed to flash outside corners or to be used as a cover patch where appropriate. It must be applied to clean, dry liner and should be pressed or rolled onto the liner.
Firestone QuickSeam™ FormFlash™Firestone QuickSeam™ FormFlash™ is an uncured EPDM strip that is factory-laminated to QuickSeam™ Tape. This strip is designed to flash inside and outside corners, pipes, penetrations and other applications as specified in the Firestone specifications and details.
Firestone QuickSeam™ Joint CoverFirestone QuickSeam™ Joint Cover is specially made to conform to irregular surfaces such as those at “T” joints, readily providing an excellent seal. Each Joint Cover is made of uncured FormFlash™ laminated to QuickSeam™ tape.
Firestone QuickSeam™ Pipe Flashing BootFirestone QuickSeam™ Pipe Flashing is specifically designed to be used for flashing of rigid round penetrations of 1"-6". It is a prefabricated pipe boot with a QuickSeam™ tape laminated to the bottom of the flange of the boot.
Firestone QuickSeam™ Splice Tape (Double-Sided Tape)Firestone QuickSeam™ Splice Tape is designed for field splicing of approved Firestone membrane panels. This double-sided seam tape works best sandwiched between two overlapped pieces of liner. It is recommended to use QuickPrime™ before peeling the paper cover off and applying the self-adhesive seam tape.
Firestone Silicone RollerThe Firestone Silicone Rubber Roller consists of a 1.5” silicone rubber-covered steel roller with a wooden handle. The roller is designed to be used to mate approved Firestone membranes with Firestone QuickSeam™ Cover Strips or QuickSeam™ Seam Tape.
Firestone Single-Ply LVOC Primer provides an LVOC option for use in cleaning and preparing either RubberGard™ EPDM or UltraPly™ TPO membranes to receive QuickSeam™ tape products.
Firestone Water Block Seal (S-20) - 10oz TubeWater Block Seal (S-20) is designed to provide a seal when used in compression as required by Firestone Details. Each 10oz tube has a coverage range of approximately 10' of 3/8" to 1/2" bead.